New Innovative Tool Holders Coming From Iscar Direct The Way In Machining Efficiency

New Innovative Tool Holders Coming From Iscar Direct The Way In Machining Efficiency

Iscar's Heliturn platform features a unique, double-sided insert with 4 cutting edges for Fast Metal Removal (FMR) turning. The completely new Heliturn is a tangentially clamped insert having a distinctive helical shaped cutting edge, useful for tremendous depths of cut and greater than common feed rate. The LNMX...-HT Heliturn insert is screw-clamped into the SLANR tool holder and reinforced by the TLN ..-HT carbide seat. This seat has ground surfaces on the top and bottom, to establish perfect contact of the insert with the tool holders. The upper rake face of this insert is mounted level with the top of the tool holder to allow chips to flow across the insert, without being complicated by clamps or the tool holder body. The 4 curved helical cutting edges provide positive radial rake angles and soft penetration into the material being cut. The reduced forces and smaller loads provide better tool lifespan, elevated stability and the ability to use particularly massive depths of cut and bigger feeds. The chipformer, distorts and breaks the chip into rib type curved fragments which can quickly be removed from the cutting area. This insert has a frontal clearance angle of 3.7 with a 6 side clearance angle to grant machining to a 90 shoulder. Depth of cut up to .315" and facing depths to .126" at up to .047" IPR are feasible with Heliturn.

When opposed to CNMG/M 16... or WNMG/M 13... insert sizes with the similar corner radius, much superior tool life can be foreseen when using the LNMX 1506..-HT insert. Iscar has recently released a smaller size to the Heliturn family - the LNMX 1104..R/L-HT insert and tool holder for the common application range of up to .197" depth of cut. The unique insert features all of the precedence of the larger insert. This heightens the economical benefit in the medium machining application range. When compared to CNMG/M 43. 12... or WNMG/M 43. 08... insert sizes with the same corner radius, a considerably better tool life can be predicted. The inserts are offered in .031, .047 and .063" tool nose radii. Heliturn inserts are presented in the most exceptional carbide grades: IC9025, IC3028 , IC428, IC907, and IC908.

The external tool holders are attainable in 1, 1.25 and 1.5" shank sizes. Boring bars are attainable in 1, 1.25 1.5 and 2" bar sizes. Also offered are exchangeable heads. These tool holders have Iscar's unique Hard Touch coating, which extends holder life and hinders corrosion. As a result of the location of this insert, machining next to the tailstock is plausible.

The high positive rake angle of these cutters allows 10-15% less power usage than normal tool holders at the same parameters.

By utilizing Iscar's Heliturn tools, immense cost savings and profitability in lathe procedures is assured.

A Brand new 80 Degree Rhombic Insert with high helical cutting edge for high metal removal rates Iscar is launching the CNMX 1207..-HTW insert family. The completely new insert has a very positive radial, helical cutting edge and a positive rake angle; a blending which substantially decreases the cutting forces. The insert's corner has a wiper arrangement which generates high surface finish even at high feed conditions, which in abundant occasions can omit a finishing cut. The corner angle is 88 degrees which provides increased strength. The CNMX inserts were constructed for heavy machining applications. Their unusual design ensures reputable, fast metal removal when using 80 degree rhombic inserts. They can be mounted on any standard tool holder that carries typical CNMG inserts, but the seat has to be substituted with a special seat: TCH 4. Iscar's R-clamp tool holders are highly suggested for heavy machining applications.

The Right Way To Buy A Megger Tester
A Megger tester is a device that is commonly used in electrical contracting to determine if the system has been properly installed.

A Wood Chipper Makes It A Lot Easier To Clear Away Brush In Your Backyard
A wood chipper can be a great tool to help clean up your yard and for making chips for landscaping. Here are a few things you need to know about when picking one.

Enjoy The Features Of Digital Caliper.
Here are some of the top reasons for considering a digital caliper. Depending on the size of your requirement you can get a caliper for about $49-100. A battery is used to power the device. It lasts and so you do not have to worry about replacing the battery.

Wood Working Made Less Difficult With Grizzly Equipments
Woodworking is a craft that requires adequate skill and creativity. The skill of a woodworker is translated to the wood with the use of appropriate wood carving tools. One brand that is popular among Northern Tools customers is Grizzly Woodworking tools.

The Best Applications For A Micro Blazer Compact Torches
The Blazer Pocket Torch is a state of the art handyman's tool that is a must-have for all men and women alike. The small pocket sized torch has the power to do a lot of jobs with great ease.

Kreg Jig Projects For Beginners
One of the leading brands when it comes to efficient and convenient tools is the Kreg Jig. In the products of Kreg Jig, the most widely used are the pocket hole jig and the kreg joint. The pocket hole is so easy to use that some described it as dummy proof.

Associated Articles

Partner Sites

Carpet Cleaners Houston

Upholstery Cleaning Houston

Houston Carpet Cleaning

Carpet Cleaners in Houston

Carpet Cleaner Houston

Bookmark this page
Delicious Digg Diigo Facebook Google Bookmarks Reddit Stumbleupon Technorati

Disclaimer Privacy Policy Contact